Skip to content
Enema bulb SP Alpina soft tip A 14 490 ml in individual packaging

Pharmacy item

Enema bulb SP Alpina soft tip A 14 490 ml in individual packaging

SKU 85279

Other products by → ALPINA PLAST LLC

All packagings

Enema bulb SP Alpina soft tip A 3 27 ml in individual packaging

12 options · from $5.94

Selected · this page

soft A 14 490

$10.60

Manufacturer leaflet

What's on the package insert

Facts from the printed manufacturer leaflet. Sections vary by drug — we only show what's actually in the box.

Indications

Intended for medical and sanitary-hygienic purposes in healthcare institutions and for individual use.
Indications for use include: the need for irrigation/washing/douching of body cavities (as recommended by a physician).

Show original (Russian)

Предназначена для медицинских и санитарно-гигиенических целей в лечебных учреждениях и для индивидуального использования.
Показаниями к применению являются: необходимость проведения ирригации/ орошения/спринцевания полостей организма (по рекомендации врача).

How to use

Usage of the product:
Fill the syringe with irrigation fluid (fill the syringe to full volume, removing any air bubbles) and perform the irrigation procedure using the stream of fluid generated by compressing the syringe bulb with your hand.
For irrigation of body cavities, use fluids (medicinal solutions as recommended by a physician).
After use, rinse the syringe with hot water and dry it.
The syringe should not come into contact with the medicinal solution for more than 30 minutes.
Before use, lubricate the syringe tip with petroleum jelly, lanolin, or another neutral fat.

Show original (Russian)

Использование изделия:
заполнить спринцовку жидкостью для ирригации (спринцовку заполняют до полного объема, удалив остатки воздуха) и провести процедуру ирригации струей жидкости, образующейся в резвльтате сжатия баллона спринцовки рукой.
Для ирригации полостей организма используются жидкости (лекарственные растворы по рекомендации врача).
После применения спринцовку промыть горячей водой, просушить.
Спринцовка не должна контактировать с лекарственным раствором более 30 минут.
Перед применением наконечник спринцовки смазать вазелином, ланолином или другим нейтральным жиром.

Composition

PVC (polyvinyl chloride) plastisol

Show original (Russian)

ПВХ (поливинилхлорид) пластизоль

Contraindications & warnings

Individual intolerance to the materials of the product.

Before use, the syringe should be disinfected by boiling in distilled water for 10±5 minutes. After the disinfection period, the syringe should be rinsed with running drinking water. After use, rinse the syringe with hot water and dry it. The syringe should be stored in a room at a temperature of +5 to +40°C and relative humidity not exceeding 80% at +25°C. The syringe should not be exposed to direct sunlight.

Attention! Do not use the syringe for oil-based products!

Disposal: when used in home settings and healthcare facilities, the product that has lost its consumer properties should be disposed of as Class A medical waste (SanPiN 2.1.7.2790) along with municipal waste. Before disposal, clean and disinfect.

Show original (Russian)

Индивидуальная непереносимость материалов изделия.

Перед применением спринцовку следует продезинфицировать методом кипячения в дистиллированной воде в течение 10±5 минут. По окончании дезинфекционной выдержки спринцовку промывают проточной питьевой водой. После применения спринцовку промыть горячей водой и просушить. Спринцовку следует хранить в помещении при температуре от +5 до +40°С и относительной влажности воздуха не более 80% при +25°С. Спринцовка не должна подвергаться воздействию прямых солнечных лучей.

Внимание! Спринцовку для маслосодержащих средств не применять!

Утилизация: при использовании в домашних условиях и лечебно-профилактических учреждениях, изделие, потерявшее потребительские свойства, подлежит утилизации по классу А (СанПиН 2.1.7.2790) медицинских отходов - вместе с коммунальными отходами. Перед утилизацией очистить и продезинфицировать.

Pharmacology

SPRAY SYRINGE SPP-ALPINA PLASTIC SOFT TIP A14 - Plastic polyvinyl chloride syringe, TYPE A No. 14
Volume: 490 ml

Classic type of syringes.
An essential item in the family medicine cabinet available in two to three sizes due to its wide range of uses - from daily procedures for the prevention of the nasopharynx to procedures commonly known as "enema."
Suitable for use at home and without age or gender restrictions.

Indications:
- for aspirating fluid from body cavities in the postoperative period;
- for flushing body cavities for therapeutic and preventive purposes.

Show original (Russian)

СПРИНЦОВКА СПП-АЛЬПИНА ПЛАСТ МЯГКИЙ НАКОНЕЧНИК А14 - Спринцовка пластизольная поливинилхлоридная, ТИП А №14
Объём: 490 мл

Классический тип спринцовок.
Является обязательной позицией семейной аптечки в двух-трех типоразмерах благодаря широте использования - от ежедневных процедур по профилактике носоглотки, до процедур под широко известным названием «клизма».
Подходит для использования в домашних условиях и без возрастного и полового ограничения.

Назначение:
-для отсоса жидкости из полостей организма в послеоперационный период;
-для промывания полостей организма в лечебно-профилактических целях.

Properties
Manufacturer
ALPINA PLAST LLC
Made in
Russia
Shipping weight
600 g
Keep at
5–40 °C
SKU
85279

RU name Спринцовка спп-альпина пласт мягкий наконечник а 14 490 мл в индивидуальной упаковке

How we fulfill

Sourced. Verified. Shipped.

Three checkpoints between the pharmacy shelf and your door. You see every one.

01

Sourced

A licensed Russian pharmacy buys it for you.

No grey-market middlemen, no warehouses we can't audit. Retail purchase, on demand, against your order.

02

Verified by photo

You see the parcel before it leaves.

A photo of your actual parcel in its original retail packaging lands in your inbox before it ships. Like this →

A real customer parcel photo, taken before dispatch Real customer parcel

03

Shipped

Tracked postage.

To 120+ countries. Most parcels arrive in 7–18 days.

Full shipping atlas

More by ALPINA PLAST LLC

See all →