Syringe 2 ml 3-component with needle 23g 0.6x30 luer type 100 pcs./Pascal/

Indications

The products can be used for various medical purposes. The indications for use depend on the purpose of medical application and are determined by the physician's prescription for performing various types of injections (subcutaneous, intradermal, intramuscular, intravenous administration), for the introduction of fluids (solutions of medicinal products) / gases (for example, medical oxygen, nitrous oxide) into a medical device (for example, a catheter, infusion system), for working with vascular catheters of various types, flushing body cavities, punctures, and aspiration of fluids/gases.

Method of Use and Doses

Before using the syringe, visually check the integrity of the individual sealed packaging. Ensure that you are using a syringe with an active expiration date. The expiration date is indicated on the individual sealed packaging. It is prohibited to use a syringe from damaged individual sealed packaging or one that has expired.
Preparation of the product for use:
1. Prepare everything necessary for the injection (syringe in individual sealed packaging, medicinal product, disinfectant wipes, waste container).
2. The volume of the syringe, the length of the needle, and the configuration must be chosen considering the volume of the medicinal product being administered, its viscosity, as well as the type of injection (intradermal, subcutaneous, intramuscular, intravenous).
3. Wash hands thoroughly with soap and wipe with a disinfectant wipe.
4. Put on single-use medical gloves.
5. Disinfect the ampoule with the medicinal product or the vial with a disinfectant.
6. Open the ampoule with the medicinal product or remove the protective cap from the vial.
7. Open the individual packaging and remove the syringe with the attached needle.
8. Carefully remove the protective cap from the needle.
9. When drawing the medicinal product from the ampoule, do so slowly, gradually lifting the bottom of the ampoule or upwards as the liquid decreases. When drawing the medicinal product from the vial, hold the vial upside down with your left hand between the second and third fingers, the fourth finger on the needle head, and use the first and fifth fingers to hold the syringe cylinder and draw the required amount of the medicinal product.
10. If using a syringe with two needles, replace the needle used to draw the medicinal product with the needle included in the individual packaging.
Procedure for using the product:
1. Prepare the injection site by disinfecting it with a disinfectant wipe.
2. Administer the injection at the prepared site, following injection technique and in accordance with the injection standard depending on the type of injection (subcutaneous, intradermal, intramuscular, intravenous).
3. Remove the syringe with the needle. Lightly press the injection site with a disinfectant wipe. The appearance of a drop of blood at the injection site is acceptable.
4. Do not replace the protective cap on the needle after the injection to avoid a needle stick injury from the used needle.
5. If necessary to aspirate fluids from body cavities, begin aspiration after removing the syringe from the packaging.
6. If necessary to irrigate body cavities, begin irrigation after filling the syringe with the irrigation solution.
7. A puncture-proof container should be used for the collection and disposal of used needles and syringes.

Composition

Manufacturing material:
Transparent cylinder made of medical polypropylene
Piston: medical polypropylene
Piston seal (gasket): synthetic rubber

Contraindications

Individual intolerance to the materials of the product.

Special Instructions

Sites for safe intramuscular injections:

• upper outer quadrant of the thigh and buttock

Recommendations for needle selection

• buttock thigh

• male 0.7x30mm (22G) 0.6x25mm (23G)

• female 0.8x40mm (21G) 0.6x25mm (23G)

Attention!

Choosing the correct needle size (diameter and length) will ensure comfortable and effective administration of the medication into the muscle tissue.

Use the recommendations for selecting the needle size according to gender and injection site.

Pharmacological action

Brand Pascal
Sterile injection syringe for single use, manufactured by "PASCAL MEDICAL" 2 ml
-Sterile
-Single-use
-Three-component
-Needle 23G (0.6x30 mm) - mounted on the syringe, removable
-The injection needle has a three-faceted laser sharpening, polishing, and silicone coating to reduce pain and trauma during injection
-The needle has a thin-walled design, which ensures more comfortable administration of liquid medicinal forms
-The color coding of the needles complies with the requirements of the international standard ISO 6009
-The connection of the syringe to the needle is of the Luer-slip type
-The position of the Luer fitting (cylinder cone) of the syringe is coaxial (concentric), i.e., the tip-cone is centered in the syringe cylinder
-The volume of the syringe is 2 ml
-The scale is graduated up to 2 ml
-The transparent cylinder with a non-erasable clear scale ensures control of the accuracy of the administered medicinal product
-The double stop ring prevents accidental withdrawal of the piston from the cylinder and leakage of the medicine during the filling of the medicinal product
-Individual packaging - blister type, ensures more convenient opening of the package and preservation of the sterility and integrity of the syringe

Description

Syringe 2 ml 3-component with needle 23g 0.6x30 luer type - this is a medical device used for injections. The sterile injection syringe has individual packaging and is intended for single use. It is made of high-quality and safe material. The needle 23g 0.6x30 is detachable. The needle does not damage tissues during insertion due to a special lubricant coating. The transparent cylinder facilitates control over the volume and clarity of the medication. The syringes have high accuracy and allow for dose control of the drug. Individual packaging ensures the preservation of sterility. Three-component syringes are a reliable and convenient tool for performing medical procedures at home or in medical institutions.