Insulin syringe 1 ml 100 units/ED three-part sterile single-use luer with needle 0.45x12 mm 100 pcs/pack

Intended for insulin injection.

Method of use (instructions for use):
Disinfect the skin at the injection site. Disinfection should be performed with ethyl or methyl alcohol. The scale division allows for the precise determination of the required dosage of the medicinal substance.
1. Before use, visually inspect the integrity of the consumer packaging. It is prohibited to use a syringe from damaged packaging.
2. Check the expiration date of the product. The use of the product after the expiration date is prohibited.
3. Open the individual packaging and remove the syringe.
4. Firmly attach the needle to the syringe cone and remove the cap.
5. Draw the medicinal preparation into the syringe.
6. Hold the syringe with the needle pointing vertically upwards and expel air bubbles by pressing on the plunger.
7. Administer the injection.
8. After the injection, remove the needle from the syringe and place it in a container for the collection and disposal of needles.
9. Dispose of the syringe and needle.

Material of manufacture:
Syringe cylinder: polypropylene.
Piston rod, rod: polyethylene/polypropylene.
Seal (gasket): PVC.
Lubricant: polymethylsiloxane liquid.
Piston seal does NOT contain latex.

No absolute contraindications for the use of the injection syringe have been identified, except in cases of individual intolerance to the components of the product.

Safety instructions and precautions:
• Before use, check the integrity of the packaging. The use of opened or damaged sterile packaging is not permitted. Do not use the product for unintended purposes.
• The syringe is intended for single use only and should be administered immediately after opening the packaging. Used needles and syringes are prohibited from being reused. Re-sterilization is not allowed.
• It is prohibited to perform injections with the same needle or syringe, changing only the needles, for multiple patients. After use, do not replace the protective cap on the needle. After use, the needle must be placed in a container for the collection and disposal of needles.

Brand PREMIER-MED/PM is the largest manufacturer of medical syringes and droppers in the Russian Federation, with an impeccable reputation for product quality, compliance with regulatory requirements, social responsibility, customer support, and service.

• Single-use sterile insulin syringe with a 1 ml capacity and a 100 ins/units scale graduated with a single-use injection needle.
• Sterile, non-toxic, apyrogenic.
• Single-use.
• Three-part.
• Conical connection of the cylinder with the injection needle - Luer type.
• Luer-lock position (cylinder cone) of the syringe - concentric.
• Finger grips on the cylinder and piston with anti-slip texture.
• Clear, indelible graduation.
• Needle 26 G x 1/2ʺ (0.45x12.0 mm) - removable, pre-attached.
• The needle tip is sharpened in three planes (laser three-level sharpening), ensuring that the puncturing effect predominates over the cutting effect during tissue penetration.
• Minimal force required for puncture.
• Longitudinal resistance to bending (elasticity).
• Strength and stability of the connection with the syringe.
• Syringe volume 1 ml.
• Scale division - 0.02.
• The stop ring prevents accidental withdrawal of the piston from the cylinder.
• The piston does not contain natural latex, eliminating the risk of allergic reactions.
• Individual sterile blister packaging - dense gas-permeable paper and transparent thermoformable film.
• The total capacity of the syringe exceeds the nominal capacity by at least 10%.
• The transparent cylinder facilitates control of the volume and clarity of the medication.
• Individual packaging ensures the preservation of sterility.

Indications: used in medical and preventive institutions of any profile and in home settings.

Conditions of use: the syringe is intended for use immediately after filling and is not designed for prolonged storage of the injected liquid.